Spark Slider Safety FAQ & Compliance Guide

No. MoltenCore spark sliders are not certified under StVZO (German Road Traffic Regulations) for public road use. They are designed for closed-circuit, track-day, supermoto-course, and private-surface use only. Riding with spark sliders on public roads may violate local traffic laws.

EU member states have varying public-road regulations. All MoltenCore products are EU GPSR (Regulation 2023/988) compliant as consumer products, meaning they meet EU product safety standards. However, public-road use depends on national vehicle modification laws. Always check your local jurisdiction before street use.

US state-by-state vehicle modification and accessory laws vary. Spark sliders are typically classified as aftermarket motorcycle accessories. Track-day and closed-circuit use is generally accepted. Public-road use depends on state vehicle code.

UK Vehicle Construction and Use Regulations apply. Track-day use is unrestricted. Public-road use depends on whether the modification affects MOT compliance.

No. MoltenCore spark sliders produce mechanical friction sparks. They contain no chemicals, no electronics, no pyrotechnic materials, and are not classified as fireworks under any EU or US regulation.

MoltenCore recommends spark sliders for users 18 years and older. Younger users may use under direct adult supervision in controlled environments only.

For motorcycle products: yes, hold a valid motorcycle license and have track-day or controlled-environment experience before installing. For skateboard products (FlameTrails Extreme): general skateboarding skill required.

Beginners should not use spark sliders for first track sessions. Master cornering, knee-dragging, or your chosen riding discipline first, then add spark sliders for visual enhancement.

Always wear motorcycle-grade visor or eye protection. For motorcycle use: full leathers, gloves, helmet (DOT/ECE certified), and motorcycle boots. For skateboard use: helmet, gloves, knee pads, elbow pads.

Spark sliders produce metallic friction particles that can travel at high velocity. A motorcycle-grade visor or safety goggles must be worn at all times during use to prevent eye injury.

Maximum 4-second scrape cycles followed by minimum 5-second cooldown. Prolonged scraping causes excessive heat in spark inserts and reduces lifespan. The included safety information sheet details exact cycle parameters.

Asphalt, concrete, and similar abrasive surfaces produce optimal sparks. Do not use on wood, plastic, glass, carpet, or non-abrasive surfaces — sparks will not generate and inserts may suffer damage.

Not recommended. Wet surfaces dramatically reduce spark generation and can cause water-related issues with hot spark inserts. Use only on dry asphalt.

MoltenCore spark sliders are classified as sporting goods and are not subject to CE marking obligation under EU consumer goods legislation. They are however fully compliant with EU GPSR (General Product Safety Regulation 2023/988) as consumer products, with 24-language safety information sheets and BAuA-registered complaint procedures.

EU Regulation 2023/988 is the General Product Safety Regulation effective December 2024 for all consumer products in the EU. MoltenCore complies through full product traceability, 24-language safety information sheets shipped with every product, registered manufacturer details, and a BAuA-registered complaint procedure.

MoltenCore is registered in Germany (Schildow, Brandenburg). Manufacturer details: Jonas Haug, Krumme Str. 21a, 16552 Schildow, Germany. BAuA-registered for product safety in Germany.

Every MoltenCore product ships with: (1) the product itself, (2) installation hardware (adhesive pads, screws, or hook-and-loop), (3) 24-language safety information sheet covering EU GPSR requirements, (4) instructions for installation and care.

Wipe with dry cloth after use. Avoid solvents, alcohol-based cleaners, or water immersion. Inserts should remain dry; surface dust can be removed gently.

30-day return window on all unused, unopened MoltenCore products. EU consumers have an additional 14-day right of withdrawal per EU Consumer Rights Directive. Used products are not returnable for hygiene and safety reasons.

Email support@moltencores.com or call +49 1525 2385963 within 48 hours of incident. MoltenCore is BAuA-registered for product complaints in Germany. Complaints involving accidents or injuries are escalated within 24 hours.

Hardware (adhesive pads, screws, hook-and-loop) is available for purchase as accessories. Spark inserts are not user-replaceable; the entire slider must be replaced once inserts are depleted.